MODs to the Fender ‘Super 60’ amplifier

Super 60 016Hello again. The Fender Super 60 was introduced in the late 1980’s as one of the dreaded ‘red knob’ series of amps, which weren’t always favourably received. This model caused some confusion for people who purchased one, as it sounds nothing like the traditional Fender amplifier models. It has a few admirers, to be sure, but the model was eventually deleted. On the plus side, this is a 60 watt 1×12 amp in a compact combo (although quite heavy as a result), with ‘clean’ and ‘overdrive’ modes plus reverb (solid-state driven, not valve/tube). The ‘clean’ tonality is good, it’s just not quite the same as a ‘blackface’ Fender.

Super 60 011On the minus side, the ‘overdrive’ mode is not that great, and the clean/overdrive tonalities and levels really don’t match up. This is due to the amount of shared circuitry, which is re-configured using opto-couplers. The bias supply voltage is not adjustable, leading to complications when installing a fresh pair of 6L6GC output valves. So, the service tech has to change resistor values as required to achieve the desired result. This is really tedious ! However, the PCB can be modified to accept a bias trimpot.

Super 60 012Which leads us to serviceability issues with these amps. As you can see from the 2nd and 3rd photos, all components (apart from transformers) are mounted to either the large main board (PCB), or the smaller front panel board. Unfortunately for the service tech, these boards are kind of ‘back-to-front’ with the solder side of the board facing upwards, and the component side facing downwards, so they cannot be inspected without stripping out the boards. The valve sockets are mounted direct to the main board.  The three preamp valves are not especially a problem, but the heat from the pair of output valves will to some extent end up being absorbed into the chassis and the main board.

Super 60 013This customer’s amp was delivered to us with low output level, a couple of badly damaged pots, and broken jacks. The input and footswitch jacks on this model are the very brittle and easy to break PCB mounting types from the 80’s and 90’s. The pots have a solid shaft with a flat section, and the original knobs naturally match this shape. The ‘clean’ mode level was considerably lower then the ‘overdrive’. We would have to completely strip out the boards anyway, so this was the perfect opportunity to implement some MODs to try and improve the ‘overdrive’ qualities plus balance up the two modes a bit better. This ‘balancing act’ doesn’t achieve absolute perfection, but is a definite improvement over the stock amp. We would suggest leaving the 3-band EQ as it is, to maintain the ‘clean’ tonality, even though the EQ is less than ideal for the ‘overdrive’ mode.

Super 60 015For those of you who have access to a schematic we modded the following components: R167 to 82K, C102/C105 to 0.01uF, R103 to 100K and R158 is the resistor to be changed for different bias levels, or else remove altogether if a trimpot is to be installed. We rebiased for 2 x 35ma Ik at B+ of 487V DC. Biasing this amp to run much hotter would be a mistake, as per the preceding paragraphs. The end result is still a compromise, but the changes will result in a fuller signal range and also more saturation available for a more modern ‘lead’ sound. Upgrading the preamp valves will improve the tone of the amp in both ‘clean’ and ‘overdrive’, and will smooth out the spiky distortion characteristic and reduce hum/noise. We have more Fender MODs to be published soon. IR.

Super 60 017p.s. the previous owner of this amp discarded the red knobs, but installed some really cheapo looking ones in their place; we ended up matching up some Fender vintage reissue black knobs, which look much better.

p.p.s. some comments on the web forums mistakenly attribute this amp to the Paul Rivera era at Fender – this is not the case, this design is dated 1988 – well after Rivera moved on to manufacture his own products. IR.

Warning !

Valves [vacuum tubes], transformers, capacitors, amplification circuits found within a guitar amplifier operate at high voltages that can cause permanent injury, disability or death. Valves [vacuum tubes] operate at high temperatures that can cause severe burns. Never attempt to repair, modify, test, work on or touch electronic equipment unless you are trained or otherwise qualified to do so. Likewise, never remove a protective cover from electronic equipment unless you are trained or otherwise qualified to do so.

Warning !

Do not remove the amplifier rear panel, the amplifier chassis, the amplifier fuses, the valves [vacuum tubes], or any other part of the amplifier with the 240V AC mains supply connected.

Advertisements

3 Responses to “MODs to the Fender ‘Super 60’ amplifier”

  1. Glenn Scott Says:

    Hello Ivan. I have a Super 60 that like alot of other owners, suffers from the ‘low clean/loud gain” problem. Im interested in getting this mod done to my amp. Did this increase the clean volume or decrease the Overdrive volume? Or was it a bit of both? Thanks for your help,
    Glenn

  2. Jan Says:

    Hello, I’d like to know about this as well! Has the mod evened out the extreme volume difference between clean and overdrive channel (at list a little)?

    • ivanrichards Says:

      hello to all Super 60 enthusiasts: sorry – I modded this specific amp last year so cannot remember in great detail – it’s not a common amp, only see one every few years – however I can state that there was an improvement to the performance of both channels, and the mods went some way to balancing up the channels but not completely, there is only so much you can do with all that shared circuitry – that is the problem; the owner of this particular amp was satisfied with the job and wouldn’t dream of going back to stock spec; IR.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s


%d bloggers like this: